How To Apply MasterEmaco® T 1060 Repair Mortar

BASF MasterEmaco T 1060 Cement-Based, Concrete Repair Mortar packaged in a 50 pound bag
BASF MasterEmaco T 1060 Cement-Based, Concrete Repair Mortar packaged in a 50 pound bag

Watch how to apply MasterEmaco T 1060 cement-based, concrete repair mortar (Video Transcript). Then learn more about the materials, tools and accessories required to do the job safely and efficiently.

MasterEmaco T 1060 Repair Mortar Application Video Transcript

  • Concrete must be structurally sound and fully cured. Surface should be prepared following current ICRI Guideline No. 310.2R surface preparation guide.
  • Surface to be repaired must be saturated-surface dry (SSD) with no standing water
  • Precondition material to 70 degrees Fahrenheit (21 degrees Celsius)
  • Add 5.5 pints (2.6 L) of potable water into a clean mixing container
  • Gradually sift in powder, 1/3 of the bag at a time, while mixing continuously at a slow speed
  • Mix for a minimum of 3 minutes to ensure a uniform, lump-free consistency
  • Using a stiff bristle broom, scrub a small quantity of mixed material into the SSD substrate
  • Work material firmly into the bottom and sides of patch. Avoid feather edging.
  • Placement time is approximately 5-10 minutes
  • Finish the completed repair as required
  • Cure with an approved curing compound that complies with ASTM C309 or ASTM C1315
  • Refer to the MasterEmaco T 1060 technical data guide for more information.

Repair Mortar Application Materials, Tools and Accessories

Materials, Tools and Accessories – Shown

  • Protective Gloves – 4-mil nitrile, disposable glove
  • Protective Clothing – Long-sleeve sweatshirt
  • MasterEmaco T 1060 Repair Mortar – Very rapid-setting, cement-based, concrete repair mortar
  • Mixing Container
  • Cordless Drill
  • Mixing Paddle
  • Stiff Bristle Broom
  • Beveled Hand Float
  • 2 inch x 4 inch Screed Board
  • Pool Trowel
  • Masonry Brush – 6 1/2 X 1 3/4
  • Concrete Curing Compound – ASTM C309 or ASTM C1315-compliant.

Precautionary Accessories – Not Shown

Refer to the MasterEmaco T 1060 Safety Data Sheet (SDS) for more information.

  • Eye Protection
  • Face Protection
  • Respiratory Protection – In case of inadequate ventilation.

Citations

Last Modified: November 13, 2019

How To Apply MasterEmaco® T 545 Repair Mortar

BASF MasterEmaco T 545 Chemical Action Repair Mortar packaged in a 50 pound bag
BASF MasterEmaco T 545 Chemical Action Repair Mortar packaged in a 50 pound bag

Watch how to apply MasterEmaco T 545 chemical action repair mortar (Video Transcript). Then learn more about the materials, tools and accessories required to do the job safely and efficiently.

MasterEmaco T 545 Repair Mortar Application Video Transcript

  • Concrete must be structurally sound and fully cured. Surface should be prepared following current ICRI Guideline No. 310.2R surface preparation guide.
  • Add 4 pints (1.9 L) of potable water into a clean mixing container
  • Gradually sift in powder, 1/3 of the bag at a time, while mixing continuously at a slow speed
  • Mix material for 90 seconds to ensure a uniform, lump-free consistency
  • Work material firmly into the bottom and sides of patch. Avoid feather edging.
  • Placement time is approximately 5 minutes
  • Level MasterEmaco T 545 and screed to the elevation of surrounding concrete. Minimal finishing is required.
  • No curing is required. Protect from rain immediately after placing.
  • Refer to the MasterEmaco T 545 technical data guide for more information.

Repair Mortar Application Materials, Tools and Accessories

Materials, Tools and Accessories – Shown

  • Protective Gloves – 4-mil nitrile, disposable glove
  • Protective Clothing – Long-sleeve sweatshirt
  • MasterEmaco T 545 Repair Mortar – Very rapid-setting, chemical action, repair mortar
  • Mixing Container
  • Cordless Drill
  • Mixing Paddle
  • 2″ x 4″ Screed Board.

Precautionary Accessories – Not Shown

Refer to the MasterEmaco T 545 Safety Data Sheet (SDS) for more information.

  • Eye Protection
  • Face Protection
  • Respiratory Protection – In case of inadequate ventilation.

Citations

Last Modified: September 13, 2019

How To Apply MasterEmaco® P 124 Primer

BASF MasterEmaco P 124 Steel Reinforcement Primer & Bonding Agent packaged in a 6-gallon kit
BASF MasterEmaco P 124 Steel Reinforcement Primer & Bonding Agent packaged in a 6-gallon kit

Watch how to apply MasterEmaco P 124 steel reinforcement primer and bonding agent (Video Transcript). Then learn more about the materials, tools and accessories required to do the job safely and efficiently.

MasterEmaco P 124 Primer Application Video Transcript

  • Concrete must be structurally sound and fully cured
  • Remove all oxidation and scale from the exposed reinforcing steel in accordance with Technical Guide No. 310.1R
  • Surface to be repaired must be saturated-surface dry (SSD) prior to the application of MasterEmaco P124, when used as a bonding agent with ICRI Technical Guide No. 310.1R
  • Precondition all components to 70 degrees Fahrenheit (21 degrees Celsius)
  • Pour contents of Part A and Part B into a clean mixing bucket
  • Blend the components for 2 minutes
  • Slowly add all of Part C. Use the appropriate drill to thoroughly mix the components.
  • Apply MasterEmaco P 124 using a stiff brush or broom
  • Work the bonding agent thoroughly into the substrate
  • When applying to rebar, two coats of 10 mils (0.25 mm) are required
  • Protect the bonding agent from direct sunlight and temperature above 95 degrees Fahrenheit (35 degrees Celsius)
  • Refer to the MasterEmaco P 124 technical data guide for more information.

Primer Application Materials, Tools and Accessories

Materials, Tools and Accessories – Shown

  • Protective Gloves – 4-mil nitrile, disposable glove
  • Protective Clothing – Long-sleeve sweatshirt
  • MasterEmaco P 124 Primer – Water-based epoxy-cementitious bonding agent, also used to coat and protect rebar
  • Cordless Drill
  • Paddle – Jiffy Mixer or similar
  • Drill Attachment/Brush
  • Brush.

Precautionary Accessories – Not Shown

Refer to the MasterEmaco P 124 Safety Data Sheet (SDS) for more information.

  • Eye Protection
  • Face Protection
  • Respiratory Protection – In case of inadequate ventilation.

Citations

Last Modified: August 30, 2019

How To Apply MasterProtect® HB 400 Coating

MasterProtect HB 400 water-based, high-build, waterproof coating in a 5 gallon pail
BASF MasterProtect HB 400 Water-Based, High-Build, 100% Acrylic, Waterproof Coating packaged in 5 gallon pail

Watch how to apply MasterProtect HB 400 water-based, high-build, 100% acrylic, waterproof coating (Video Transcript). Then learn more about the materials, tools and accessories required to do the job safely and efficiently.

MasterProtect HB 400 Coating Application Video Transcript

  • How To Apply MasterProtect HB 400 Coating
  • Ensure substrate is structurally sound, fully cured, dry and clean
  • Mix thoroughly before applying. Apply by brush, roller or sprayer.
  • Apply coating using an ‘N’ pattern
  • Cross-roll through coating to ensure uniform wet mil thickness
  • Check wet film thickness to ensure application at specified rate
  • Back-roll in same direction to create a uniform appearance
  • Refer to the MasterProtect HB 400 technical data guide for more information.

Coating Application Materials, Tools and Accessories

Materials, Tools and Accessories – Shown

  • Protective Gloves – 4-mil nitrile, disposable glove
  • Protective Clothing – Long-sleeve sweatshirt
  • MasterProtect HB 400 Coating – For above-grade concrete, masonry, stucco, and EIFS
  • Low Speed Drill
  • Coating Mixing Paddle – Double ribbon agitator
  • Roller – Adjustable handle and 3/4 – 1 1/4 inch nap roller cover
  • Wet Film Thickness Gauge/Comb.

Precautionary Accessories – Not Shown

Refer to the MasterProtect HB 400 Safety Data Sheet (SDS) for more information.

  • Eye Protection
  • Face Protection
  • Respiratory Protection – In case of inadequate ventilation.

Citations

Last Modified: August 16, 2019